CWR300ND-AU300M ADSL2+Wireless Router
- 8 - 2 Hardware Installation Step 1 Connect the ADSL interface of the device and the Modem interface of the splitter through a telephone cable.
- 98 - Click Run Diagnostic Test to start testing.
MD120109-01HOTLINE .AUSTRALIA :1300 765 663 .NEW ZEALAND :0800 100 236
- 9 - Figure 1 Connection diagram (Without connecting telephone sets before the splitter) Connection 2 Figure 2 shows the connection when the split
- 10 - Note: When connection 2 is used, the filter must be installed close to the telephone cable. See Figure2. Do not use the splitter to replace
- 11 - 3 Web Configuration This chapter describes how to configure the router by using the Web-based configuration utility. 3.1 Access the Route
- 12 - When you log in as a common user, you can check the status of the router, but can not configure the most of the settings. Note: In the We
- 13 - In the navigation bar, choose Wizard. The page shown in the following figure appears. You may change the password by entering a new one, or
- 14 - The following table describes the parameters of this page: Field Description State You can disable or enable NTP function. You have to enable
- 15 - The following table describes the parameters of this page: Field Description Country Select the Country from the drop-down list. ISP Select t
- 16 - The following table describes the parameters of this page: Field Description WLAN Interface You can choose Enable or Disable. By default, W
- 17 - Field Description frames before transmitting over the wireless network. Wi-Fi protected access (WPA) is a subset of the IEEE802.11i securi
CWR300ND User Manual
- 18 - Note: If the WAN connection type is set to PPPoA, the parameters of the WAN connection type are the same as those of PPPoE. For the paramete
- 19 - The following table describes the parameters of this page: Field Description WLAN Interface You can choose Enable or Disable. By default, W
- 20 - Field Description frames before transmitting over the wireless network. Wi-Fi protected access (WPA) is a subset of the IEEE802.11i securi
- 21 - The following table describes the parameters of this page: Field Description Country Select the Country from the drop-down list. ISP Selec
- 22 - Connection Type You can select LLC or VC-Mux. VPI/VCI VPI: Virtual path between two points in an ATM network. Its valid value range is fr
- 23 - Field Description WLAN Interface You can choose Enable or Disable. By default, WAN interface is enabled. You need to enable WAN interface, an
- 24 - 1483 Routed/1483 MER: Static IP
- 25 - The following table describes the parameters of this page: Field Description Country Select the Country from the drop-down list. ISP Selec
- 26 - Connection Type You can select LLC or VC-Mux. VPI/VCI VPI: Virtual path between two points in an ATM network. Its valid value range is fr
- 27 - The following table describes the parameters of this page: Field Description WLAN Interface You can choose Enable or Disable. By default, WA
- 1 - Contents 1 Introduction ...- 3 - 1.1 Packin
- 28 - Field Description network. Wi-Fi protected access (WPA) is a subset of the IEEE802.11i security specification draft. WPA2 Mixed is th
- 29 - Note: If the WAN connection type is set to 1483 Routed, the parameters of the WAN connection type are the same as those of 1483 MER: Static
- 30 - 3.3.2 LAN Choose Status > LAN. The page that is displayed shows basic LAN settings of the router. In this page, you can view the LAN IP
- 31 - 3.3.4 WAN Choose Status > WAN. The page that is displayed shows some basic WAN settings of the router. In this page, you can view basi
- 32 - 3.3.5 Port Mapping Choose Status > Port Mapping. In this page, you can view the mapping relation and the status of port mapping. 3.3.6
- 33 - 3.3.6.1 Traffic Statistic Click Traffic Statistic in the left pane. The page shown in the following figure appears. In this page, you can vie
- 34 - 3.3.7 ARP Table Choose Status > ARP Table. In the ARP Table page, you can view the table that shows a list of learned MAC addresses.
- 35 - 3.4 Network In the navigation bar, click Network. The Network page displayed contains LAN, WAN and WLAN. 3.4.1 LAN Choose Network > L
- 36 - Field Description IP Address Enter the IP address of LAN interface. It is recommended to use an address from a block that is reserved for pr
- 37 - The following table describes the parameters of this page: Field Description DHCP Mode If set to DHCP Server, the router can assign IP add
- 2 - 3.6.3 Port Mapping ...- 83 - 3.6.4 QoS...
- 38 - Field Description retains the assigned IP addresses before the IP addresses change. Domain Name Enter the domain name if you know. If you le
- 39 - Field Description example, 00-A0-C5-00-02-12. Expiry (s) It displays the lease time. The lease time determines the period that the host retai
- 40 - In the DHCP Mode field, choose DHCP Relay. The page shown in the following figure appears.
- 41 - The following table describes the parameters and buttons of this page: Field Description DHCP Mode If set to DHCP Relay, the router acts a s
- 42 - Field Description Table. Delete Selected Select a row in the DHCP Static IP Table, then click it, this row is deleted. Reset Click it to r
- 43 - The following table describes the parameters of this page: Field Description Default Route Selection You can select Auto or Specified. VPI
- 44 - Field Description Type You can choose Fixed IP or DHCP. If select Fixed IP, you should enter the local IP address, remote IP address and s
- 45 - The following table describes the parameters and buttons of this page: Field Description Protocol It displays the protocol type used for
- 46 - Field Description Idle Time (s) If choose Connect on Demand, you need to enter the idle timeout time. Within the preset minutes, if the r
- 47 - The following table describes the parameters of this page: Field Description VPI The virtual path identifier of the ATM PVC. VCI The vir
- 3 - 1 Introduction The CWR300ND is an ADSL access device that supports multiple line modes. It provides one 10/100Base-T Ethernet interface at t
- 48 - 3.4.2.3 ADSL Setting Click ADSL Setting in the left pane, the page shown in the following figure appears. In this page, you can select the DS
- 49 - The following table describes the parameters of this page: Field Description Band Choose the working mode of the modem. You can choose from
- 50 - Field Description the modem. Channel Number A channel is the radio frequency used by 802.11b/g/n wireless devices. There are 13 channels (fr
- 51 - The following table describes the parameters of this page: Field Description Encryption Configure the wireless encryption mode. You can cho
- 52 - Field Description Key differences between WPA and WEP are user authentication and improved data encryption. Set WEP Key It is available wh
- 53 - The following describes the parameters of this page: Field Description Key Length Choose the WEP key length. You can Choose 64-bit or 128-bi
- 54 - Choose Allow Listed as the access control mode to enable white list function. Only the devices whose MAC addresses are listed in the Curren
- 56 - The following describes the parameters of this page: Field Description Enable VAP0/1/2/3 Tick to enable VAP0 /1/2/3, or untick the check box
- 57 - The following table describes the parameters of this page: Field Description Authentication Select the modem operating in the open system
- 4 - Proper space left for heat dissipation is necessary to avoid damage caused by overheating to the device. The long and thin holes on the dev
- 58 - Field Description In the encryption authentication, the wireless client connects to the modem through the shared key. Data Rate Choose th
- 59 - 3.4.3.6 WPS Choose WLAN > WPS and the following page appears. There are two ways for the wireless client to establish the connection with
- 60 - 3.5 Service In the navigation bar, click Service. In the Service page that is displayed contains DNS, Firewall, UPNP, IGMP Proxy, TR-069 an
- 61 - Field Description enabled PVC(s) during the connection establishment.Set DNS Manually Select it, enter the IP addresses of the primary and s
- 62 - The following table describes the parameters of this page: Field Description DDNS provider Choose the DDNS provider name. You can choose Dyn
- 63 - 3.5.2.2 MAC Filter Click MAC Filter in the left pane, the page shown in the following figure appears. Entries in the table are used to restr
- 64 - 3.5.2.3 URL Blocking Click URL Blocking in the left pane, the page shown in the following figure appears. This page is used to block a fully
- 65 - The following table describes the parameters and buttons of this page: Field Description URL Blocking Capability You can choose Disable or
- 66 - The following table describes the parameters of this page: Field Description Service Type You can select the common service type, for exam
- 67 - Field Description LAN Open Port Enter the port number of the specified service type.LAN IP Address Enter the IP address of the virtual serv
- 5 - LED Color Status Description On The Internet connection is normal in the routing mode (for example: PPP dial-up is successful), and no Int
- 68 - 3.5.2.6 DMZ Setting Demilitarized Zone (DMZ) is used to provide Internet services without sacrificing unauthorized access to its local privat
- 69 - 3.5.2.8 ALG Setting Click ALG Setting in the left pane, the page shown in the following figure appears.
- 70 - 3.5.2.9 Anti-DoS Denial-of-Service Attack (DoS attack) is a type of attack on a network that is designed to bring the network to its knees by
- 71 -
- 72 - 3.5.3 UPNP Choose Service > UPnP, the page shown in the following figure appears. This page is used to configure UPnP. The system acts
- 73 - 3.5.5 TR-069 Choose Service > TR-069, the page shown in the following page appears. In this page, you can configure the TR-069 CPE.
- 74 -
- 75 - The following table describes the parameters of this page: Field Description ACS URL The URL of the auto-configuration server to connect to
- 76 - can configure the IP address for Access Control List (ACL). If ACL is enabled, only the effective IP address in the ACL can access the router
- 77 - Field Description access the router. Services Allowed You can choose the following services from LAN: Web, Telnet, FTP, TFTP, SNMP, or PING.
- 6 - The following table describes the interfaces of the device: Interface/Button Description WPS/WLAN Press the button silently less than 1s
- 78 - The following table describes the parameters and buttons of this page: Field Description Direction Select Select the router interface. You c
- 79 - The following table describes the parameters and button of this page: Field Description Aging Time If the host is idle for 300 seconds (d
- 80 - 3.6.2 Routing Choose Advance > Routing, the page shown in the following figure appears. The page that is displayed contains Static Route
- 81 - Field Description Interface The interface for the specified route. Add Route Click it to add the new static route to the Static Route Tabl
- 82 - The following table describes the parameters and buttons of this page: Field Description RIP Select Enable, the router communicates with o
- 83 - Field Description RIP1 messages only. Choose RIP2 indicates the router multicasts RIP2 messages only. Add Click it to add the RIP interfa
- 84 -
- 85 - The procedure for manipulating a mapping group is as follows: Step 1 Select Enable to enable this function. Step 2 Select a group from the
- 86 -
- 87 - The following table describes the parameters and buttons of this page: Field Description IP QoS Select to enable or disable IP QoS function
- 7 - 1.5 Features The device supports the following features: Various line modes External PPPoE dial-up access Internal PPPoE/PPPoA dial
- 88 - 3.6.5 SNMP Choose Advance > SNMP, the page shown in the following figure appears. You can configure the SNMP parameters. The following
- 89 - 3.6.6 Others Choose Advance > Others, the page shown in the following figure appears. 3.7 Admin In the navigation bar, click Admin. T
- 90 - The following table describes the parameters and button of this page: Field Description Reboot from You can choose Save the current configur
- 91 - The following table describes the parameters and button of this page: Field Description Select File Click Browse to select the firmware fil
- 92 - 3.7.4 Password Choose Admin > Password, the page shown in the following figure appears. By default, the user name and password are admi
- 93 - The following table describes the parameters of this page: Field Description User Name Choose the user name for accessing the router. You
- 94 - 3.7.5 Time Zone Choose Admin > Time Zone, the page shown in the following figure appears. You can configure the system time manually or
- 95 - The following table describes the parameters of this page: Field Description System Time Set the system time manually. NTP Configuration St
- 96 - The following table describes the parameter and button of this page: Field Description Host Enter the valid IP address or domain name. Ru
- 97 - Click Run Loopback to start testing. 3.8.3 ADSL Choose Diagnostic > ADSL. The page shown in the following figure appears. It is used for
Commentaires sur ces manuels