Soniq QFM32A Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Soniq QFM32A. SONIQ QFM32A User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 3
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
ASSEMBLY INSTRUCTIONS
FOR ADJUSTABLE FLAT PANEL WALL MOUNT
This product is designed to mount flat panel televisions weighing up to 132lbs/60kgs to a vertical wall with
maximum flat panel wall mount installing hole dimensions 75.5cm (width) x 48cm (height). It allows you to
effortlessly tilt your new television up or down without using tools.
Before installing our wall mount product,
please make sure your unit installing hole
dimensions is covered in product maximum
supported range.
Be careful to make sure there are no missing or defective parts.
Never use defective parts.
Improper installation may cause damage or serious injury.
Note The included hardware is for mounting on walls with wood stud construction.
If you are uncertain about the nature of your wall, consult an expert.
Please consult your hardware or installation professional for proper mounting to other types or walls.
The supplied hardware is not for steel.
Safety Warning:
SUPPLIED PARTS:
g: Plastic Cover x4
d: 1”Diameter Tube 2x
r4: Vise Assembly (small) x
bx: Arm Assembly 1 c: Monitor Brackets x2a Wall Plate x 1
e: 61/4x2.5"Lag Bolt x f: 6Concrete Anchor x h: M8 Machine Screw
M8x25 x4 and M8x40 x4
i: x4M6x30 Machine Screw
m: M4/M5 Washer x12
p: Axle Pin & Safety Bolt x4
n: Plastic Spacer x4
l: Lag Bolt Washer x10
j: 4M5x30 Machine Screw x k: M4x30 Machine Screw x4
q : Axle Pin & Safety Bolt 2x
s2: Vise Assembly (big) x
t: Allen Key(2)
1a.BRICK,SOLID CONCRETE AND CONCRETE BLOCK MOUNTING:
1b. MOUNTING THE WALL PLATE: be mounted to two wood studs.
Use the (a) as a template to mark 6 hole locations on the
wall. Three in the top row of slots and three more in the bottom row. Make sure these holes are level and there is at least 150mm between any
two holes. Pre-Drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a Concrete Anchor (f) into each of these holes, Pre-
Drill these holes with a 5mm flush with the concrete surface even if there is a layer of drywall or other material in front. Attach the to
the wall using 6 Lag bolts (e) and 6 M4 / M5 Washer (m).
The (a) Use a high quality stud sensor to locate two
adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail shown in diagram 1-A. Pre-drill a 3mm deep hole
at the desired height in each stud using a 4mm drill bit. Make sure these holes are in the center area of the studs and level with each other.
Use the as a template to mark the location of the second hole in each stud. Pre-drill these two holes using the 4 drill bit as well.
Attach the to the wall using for the four Lag Bolts (e). Make sure the is oriented so the flat surface in the center of the
plate in against the wall shown in diagram 1-B.
Wall Plate
Wall Plate
wall plate
Wall plate
Wall Plate Wall Plate
WARNING :Tighten Lag Bolts (e) only until Lag Bolt Washer (l) is pulled firmly against the Wall Plate (a).DO NOT OVERTIGHTEN THE
BOLTS!
MUST
o: Plastic Spacer x4
75.5cm
48cm
Maximum supportwidth
wall mountinstalling hole
Maximum support
high wallmount
installing hole
Vue de la page 0
1 2 3

Résumé du contenu

Page 1 - ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONSFOR ADJUSTABLE FLAT PANEL WALL MOUNTThis product is designed to mount flat panel televisions weighing up to 132lbs/60kgs to a ver

Page 2 - M6 safety Bolt

3.Attach the monitor bracket to the television:3a.Select the television mounting hardware:Always make sure the television is unplugged before threadin

Page 3 - Diagram11 Diagram12

Diagram11 Diagram124.Hang the TV onto the wall plat: after Monitor Brackets are mounted on the TV, lift the TV with its back to the wall plate and han

Commentaires sur ces manuels

Pas de commentaire